[Clem]

Download your Rider's Manual here:
BMW Motorrad International

2015 Threaded Fasteners:
Front wheel Brake caliper on telescopic forks
M10 x 65 28 ft/lb/ (38 Nm)
Quick-release axle in telescopic fork
M20 x 1.5 37 ft/lb (50 Nm)
Clamping screw for quick-release axle in telescopic fork
M8 x 35 Tighten the screws 6 times, alternating
between one and the other each time
14 ft/lb (19 Nm)

Rear wheel:
Tighten rear wheel on wheel flange
M10 x 1.25 x 40 Tighten diagonally
44 ft/lb (60 Nm)

2015 Technical data:
Mirror arm Mirror (locknut) on adapter
Left-hand thread, M10 x 1.25 16 ft/lb (22 Nm)
Adapter on clamping block
M10 x 14 - 4.8 18 ft/lb (25 Nm)
Handlebars Clamping block (handlebar clamp) on fork bridge
M8 x 35 Tighten on block in front (in the direction
of travel)
14 ft/lb (19 Nm)


Here is a link to another VerticalScope / MC.com sister forum R1200GS.INFO
http://www.r1200gs.info/misc/torque.html
An excellent and more complete set of Torque Values for the _LC GS Boxer
Painstakingly created from the BMW REP-ROM - Respect and Appreciation to you Sirs.
Thanks to all those who so carefully assembled this information in such easy to use fashion.

 

[Hunger4tq]

Thank you!!! Been looking for this info.

 

[justcharlie]

Thanks!

Where did you get these? I haven't been able to find a service manual for the 2015 R12R yet.

 

[pierre]

thanks for the link

 

[justcharlie]

Thanks!

Where did you get these? I haven't been able to find a service manual for the 2015 R12R yet.

Well, if I had RTFM more carefully I would've known these torque settings are in the owner's manual that came with the bike!

Still, I want the shop manual so that eventually I can do all my own wrenching. I'm sort of embarrassed that I took it into the dealer for the 600 mile run-in check. All they do for that ~$300 is change oil, filter, and gear oil; plus check other fluid levels and look for loose parts.

 

[rtbain]

Thanks for the information! I am looking for the torque values on the triple tree clamps for a 2016 'R.

 

[Panzermann]

I assume you mean triple clamp to fork tube. 19 Nm
Tighten bottom bolts three times each in alternate sequence to ensure even clamping.

 

[Stricko]

Download your Rider's Manual here:
BMW Motorrad International

2015 Threaded Fasteners:
Front wheel Brake caliper on telescopic forks
M10 x 65 28 lb/ft (38 Nm)
Quick-release axle in telescopic fork
M20 x 1.5 37 lb/ft (50 Nm)
Clamping screw for quick-release axle in telescopic fork
M8 x 35 Tighten the screws 6 times, alternating
between one and the other each time
14 lb/ft (19 Nm)

Rear wheel:
Tighten rear wheel on wheel flange
M10 x 1.25 x 40 Tighten diagonally
44 lb/ft (60 Nm)

2015 Technical data:
Mirror arm Mirror (locknut) on adapter
Left-hand thread, M10 x 1.25 16 lb/ft (22 Nm)
Adapter on clamping block
M10 x 14 - 4.8 18 lb/ft (25 Nm)
Handlebars Clamping block (handlebar clamp) on fork bridge
M8 x 35 Tighten on block in front (in the direction
of travel)
14 lb/ft (19 Nm)

Thanks Clement I used these today when refitting both front & rear wheels after getting new tyres fitted

 

[Raimisbmw]

Hello this red marks bolt torque ??? Please help !!!! Thanks

 

[Anthonyp0808]

Is this it? Installing clutch plate .. You will need one hell of a torque wrench ..

.

 

[Boxflyer]

This handy sheet that I made covers lots of the routine maintenance on the WetHead bikes. There are some differences between my RT and other models, but this is a starting point for you to make your own notes specific to what your bike is.
Hope this helps.
R1200LC Torque Sheet

 

[Gabriel]

hello bmw peoples , maybe some body can help me .
i need torque of the nut 3 but on the oposite side . there work side by side with a bearing .
maybe is the same as 150nm but the nut is a litllte small
thanks
gabriel